Novel fixed‐site–carrier polyvinylamine membrane for carbon dioxide capture

Fixed‐site–carrier membranes were prepared for the facilitated transport of CO₂ by casting polyvinylamine (PVAm) on various supports, such as poly(ether sulfone) (PES), polyacrylonitrile (PAN), cellulose acetate (CA), and polysulfone (PSO). The cast PVAm on the support was crosslinked by various methods with glutaraldehyde, hydrochloric acid, sulfuric acid, and ammonium fluoride. Among the membranes tested, the PVAm cast on polysulfone and crosslinked by ammonium fluoride showed the highest selectivity of CO₂ over CH₄ (>1000). The permeance of CO₂ was then measured to be 0.014 m³ (STP)/(m² bar h) for a 20 μm thick membrane. The effect of the molecular weight of PVAm and feed pressure on the permeance was also investigated. The selectivity increased remarkably with increasing molecular weight and decreased slightly with increased pressure in the range of 1 to 4 bar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4326–4336, 2004     

Pressure and temperature dependence of the gas‐transport properties of dense poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] membranes

The gas‐transport properties of poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] (6FDA‐2,6‐DAT) have been investigated. The sorption behavior of dense 6FDA‐2,6‐DAT membranes is well described by the dual‐mode sorption model and has certain relationships with the critical temperatures of the penetrants. The solubility coefficient decreases with an increase in either the pressure or temperature. The temperature dependence of the diffusivity coefficient increases with an increase in the penetrant size, as the order of the activation energy for the diffusion jump is CH₄ > N₂ > O₂ > CO₂. Also, the average diffusion coefficient increases with increasing pressure for all the gases tested. As a combined contribution from sorption and diffusion, permeability decreases with increases in the pressure and the kinetic diameter of the penetrant molecules. Even up to 32.7 atm, no plasticization phenomenon can be observed on flat dense 6FDA‐2,6‐DAT membranes from their permeability–pressure curves. However, just as for other gases, the absolute value of the heat of sorption of CO₂ decreases with increasing pressure at a low‐pressure range, but the trend changes when the feed pressure is greater than 10 atm. This implies that CO₂‐induced plasticization may occur and reduce the positive enthalpy required to create a site into which a penetrant can be sorbed. Therefore, a better diagnosis of the inherent threshold pressure for the plasticization of a glassy polymer membrane may involve examining the absolute value of the heat of sorption as a function of pressure and identifying the turning point at which the gradient of the absolute value of the heat of sorption against pressure turns from a negative value to a positive one. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 354–364, 2004     

Behavior of cellulose in NaOH/Urea aqueous solution characterized by light scattering and viscometry

Cellulose was dissolved in 6 wt % NaOH/4 wt % urea aqueous solution, which was proven by a ¹³C NMR spectrum to be a direct solvent of cellulose rather than a derivative aqueous solution system. Dilute solution behavior of cellulose in a NaOH/urea aqueous solution system was examined by laser light scattering and viscometry. The Mark–Houwink equation for cellulose in 6 wt % NaOH/4 wt % urea aqueous solution at 25 °C was [η] = 2.45 × 10^?2 weight‐average molecular weight (M_w)^0.815 (mL g^?1) in the M_w region from 3.2 × 10⁴ to 12.9 × 10⁴. The persistence length (q), molar mass per unit contour length (M_L), and characteristic ratio (C_∞) of cellulose in the dilute solution were 6.0 nm, 350 nm^?1, and 20.9, respectively, which agreed with the Yamakawa–Fujii theory of the wormlike chain. The results indicated that the cellulose molecules exist as semiflexible chains in the aqueous solution and were more extended than in cadoxen. This work provided a novel, simple, and nonpollution solvent system that can be used to investigate the dilute solution properties and molecular weight of cellulose. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 347–353, 2004     

Cl/HN3/I2全气相化学激光体系的化学动力学模拟计算

 对Cl/HN₃/I₂产生NCl(a)/I激光的过程进行了化学动力学计算，主要考察了Cl,HN₃和I₂的初始粒子数密度及其配比对小信号增益系数的影响。结果发现,当温度为400K, 初始Cl粒子数密度为1×10¹⁵，1×10¹⁶和1×10¹⁷cm^-3时,小信号增益系数分别达到1.6×10^-4,1.1×10^-3和1.1×10^-2cm^-1，获得最佳小信号增益系数的HN₃和I₂的初始粒子数密度分别为初始Cl粒子数密度的1～2倍和2%～4%。同时，对Cl，HN₃和I₂配比对小信号增益系数和增益持续时间的影响进行了讨论。     

Synthesis of Cationic PEM Emulsion and Application in Waste Water Treatment

Cationic polymer as a kind of flocculant is widely applied in purification treatment of waste water. Because it has positive charge group, it is able to connect strongly the suspended matters, short cellulose and other microparticles. The research on synthesis of cationic polymer and application in treatment of waste water is very universal abroad. But domestic research on those is not general. The technology of synthesis of PEM is simple, and the production cost is low. It is easy to apply in treatment of waste water.Synthesis of PEM Emulsion FlocculantSome distilled water, PVA(poly(vinyl alcohol)), EA(ethyl acrylate), and K2S2O8(potassium persulfate) were put into reaction vessel. Kept stirring up under nitrogen. When heated the solution to 40℃, dropped the water solution of MTA[(2-methacryloxylethyl)trimethyl ammonium].Maintained the temperature at 70℃, reacted about 7-8 hours. Then got the PEM emulsion. Changed the ratio of EA and MTA. Obtained a series of PEM emulsions.Stability and Convertibility of PEM EmulsionThe test results showed that when the EA/MTA was 85/15, the PEM emulsion was most stable.When the total monomer quantity was 35%, the convertibility of PEM emulsion was the highest,i.e.98.6%.The MTA Copolymerization Ratio and Morphology of PEM EmulsionWhen the monomers EA/MTA=85/15 and total monomer quantity was 35%, the MTA copolymerization ratio of PEM emulsion was 95.15%(the highest), and the PEM emulsion was some microspheres with 100-180nm of diameter.The Test Results of PEM Emulsion in Treatment of Waste Water The PEM emulsion flocculant was applied in treatment of waste water of paper mill, and measured the precipitation time(t) and transmittancy(T). The test results were showed in table 1. The optimum value of PEM which was able to make the waste water of paper mill into clear water was 0.008%.     

PURIFICATION OF L-METHIONINE AND N-ACETYL-D-METHIONINE FROM THE MIXTURE OF ENZYMATICALLY DEACYLATED N-ACETYL-DL-METHIONINE

1. INTRODUCTION Methionine, namely 2-amido-4-thiomethyl butyric acid with a structure of CH3SCH2CH2CHCOOH, is one of the essential amino acids and has two natural enantionmers, D and L-methionine. The mixture of L- and D-isomers can be used as analeptics or nutritive additives to maintain the equilibrium of amino acids of feed [1,2]. L-methionine can release active methyl and accelerate the synthesis of choline, which further speeds up the conversion of the lipid accumulated in liv…     

Acetalation and Ketalation Catalyzed by SO42-/TiO2-MoO3

The catalytic activities of SO42-/TiO2-MoO3 in synthesizing cyclohexanone ethylene ketal,cyclohexanone 1,2-propanediol ketal, 2-propyl-1,3-dioxolane, 4-methyl-2-isopropyl-1,3-dioxolane,2-isopropyl-1,3-dioxolane, 4-methyl-2-isopropyl-1,3-dioxolane, butanone ethy-lene ketal and butanone 1,2-propanediol ketal were reported. It has been demonstrated that SO42-/TiO2-MoO3 is an excellent catalyst. Various factors concerned in this reaction have been investigated. The optimum conditions have been found, that is, the molar ratio of aldehyde/ketone to alcohol was 1:1.5 or 1:1.3,the mass ratio of the catalyst used to the reactants was 0.25～1.5%, and the reaction time was 45～60 min. Under this conditions, the yield of cyclohexanone ethylene ketal is 82.7%, cyclohexanone 1,2-propanediol ketal is 83.4%, the yield of 2-propyl-1,3-dioxolane is 68.1%,4-methyl-2-isopropyl-1,3-dioxolane is 87.5%, the yield of 2-isopropyl-1,3-dioxolane is 70.7%,4-methyl-2-isopropyl-1,3-dioxolane is 82.5%, the yield of butanone ethylene ketal is 74.1%, and butanone 1,2-propanediol ketal is 94.9%.Some equation and experiment results concerned of the synthetic acetals or ketals were listed as follows.     

Hydrothermal Synthesis and Characterization of a Novel Two-dimensional Framework Materials Constructed from Polyoxometalate and Coordination Groups: [H_2Mo_(5.5)V_(10.5)O_(40)(PO_4)][Cu(en)_2]_4·7H_2O

IntroductionPolyoxometalatesarewidelystudiedfortheirin terestingapplicationsincatalysis ,electronicconduc tivity ,magnetism ,nonlinearopticsandmedicine[1— 4 ] .Whilethemechanismofthesynthesisofpolyoxometalatesremainselusiveandisoftende scribedasself assembly ,thereseemstobeanincreas inguseofthecombinationofthehydrothermalmethodandthestructure directingtemplate .There searchwiththismethodhasdemonstratedthatanum beroftransitionmetaloxides ,typicallyreducedmolybdenumoxides ,mixedvalancevanadiumo…     

Self-assembly of Carboxyl Functionalized Polystyrene Nanospheres into Close-packed Monolayers via Chemical Adsorption

The polyacrylic acid functionalized polystyrene nanospheres were synthesized and self-assembled into irregular, densely packed monolayers in non-aqueous media. The polymer nanoparticles were chemically adhered to substrates. The morphologies of the resulting films were investigated. The impact of the volume fraction of alcohol in the mixed solvents on the particle adsorption and fabrication of nanosphere assembled films was examined.     

Nickel Chloride Promoted Glaser Coupling Reaction in Hot Water

A Glaser coupling reaction of terminal alkynes in the presence of nickel chloride withoutany organics and bases in hot water has been developed, which produces the correspondinghomo-coupling products in good yields.